Promag CON-485 Series Operations Instructions Page 86
- Page / 98
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10 Technical data Memo-Graph S
86 Endress+Hauser
Digital inputs 10.2.2 Digital I/O board (socket 1, socket 2)
15 digital inputs
as per DIN 19240: Logic “0” equals -3 to +5 V
Active at logic “1” equals +12 to +30 V
max. 25 Hz, max. 32 V, input current max. 2 mA
Selectable function per input: control input (time synchronisation, set-up lock, text display, group
display, display switch off, product/batch start/stop, product selection (BCD), save text, text selec-
tion (BCD), save curve, reset batch number), impulse counter, log in/out, operating time counter,
combination event + operating time counter
Digital inputs 10.2.3 Power supply board (socket 3)
7 digital inputs:
as per DIN 19240: logic “0” equals -3 to +5 V
Active at logic “1” equals +12 to +30 V
max. 25 Hz, max. 32 V, input current max. 2 mA
Selectable function per unit: control input (time synchronisation, set-up lock, text display, group dis-
play, display switch off, product/batch start/stop, product selection (BCD), save text, text selection
(BCD), save curve, reset batch number), impulse counter, log in/out, operating time counter, com-
bination event + operating time counter
Thermocouples Type T (Cu-CuNi):
-270 to +400 °C / -454 to 752 °F
0.05 K / 0.25 % of measurement range from -200 °C /
-328 °F
Type U (Cu-CuNi):
-200 to +600°C / -328 to 1112 °F
0.1 K / 0.25 % of measurement range from 0 °C /
32 °F
Type W3 (W3Re/W25Re):
0 to +2315 °C / 32 to 4199 °F
0.2 K / 0.25 % of measurement range
Type W5 (W5Re/W26Re):
0 to +2315 °C / 32 to 4199 °F
0.2 K / 0.25 % of measurement range
Selectable cold junction compensation (DIN IEC 584): internal compensation of the terminal temperature (incl. max. error:
± 2 K; front end calibration), or external: 0°C, 20°C, 50°C, 60°C, 70°C, 80°C
Cable open circuit monitor, can be switched off (> approx. 20 kOhm, display “
_ _ _ _ _
” on screen)
Input impedance 1 MOhm (DIN IEC 584)
Resistance
thermometer
Pt100, Pt500, Pt1000:
-100 to +500 °C / -148 to 932 °F
0.05 K / 0.20 % of measurement range
DIN EN 60751
Pt100:
-50 to +150 °C / -58 to 302 °F
0.05 K / 0.25 % of measurement range; max. measurement
error between 71 °C / 160 °F and 77 °C /
171 °F: 0.5 °C / 0.9 °F
Ni100:
-60 to +180 °C / -76 to 356 °F
0.05 K (DIN 43760 / DIN IEC 751) / 0.25 % of measure-
ment range
Two- or three-wire connection (screened cable), (cable compensation ≤ 50 Ohm)
Measurement current: < 1 mA
Cable open and short circuit monitor: Display “
_ _ _ _ _
” on screen
PROFIBUS-DP
measurement
range
Dependent on connected PROFIBUS components
Scan cycle 125 ms/channel; 8 or16 channels in 1 s
Maximum allo-
wable potential
difference
Channel - channel: DC 60 V, AC 60 Vp (only safe low voltage)
Channel - ground: DC 60 V, AC 60 Vp (only safe low voltage)
Damping Presettable time constant: 0...999.9 seconds, per analogue input,
System base damping can be ignored
Description Mesurement range Signal resolution/accuracy
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Related products and manuals for Measuring & layout tools Promag CON-485 Series
(40 pages)© 2020, manymanuals.com. All rights reserved. | 2.241 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals