Promag CON-485 Series Operations Instructions Page 54
- Page / 98
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5 Operation / adjusting device settings - Set-up to commissioning Memo-Graph S
54 Endress+Hauser
Service: General sub-menu
Information for service technicians, e.g. for questions about the device/device fault
Set-up -> Service -> General
SW version Device software version. Please state this code if you have questions about the device.
Last power on Please state this code if you have questions about the device.
Last C-assertion Please state this code if you have questions about the device.
PRESET
" Caution!
Resets all parameters to the factory settings.
All previous values, settings and contents of the memory are deleted.
Display addresses Displays the address of the current position, as well as the help texts.
Test functions EPLD value display: instead of the scaled instantaneous value, the EPLD frequency value (raw value) is output.
Special measurement display: displays the Delta_agnd(4), Delta_agnd_U_I(5), U_P(6), U_I(7), U_U(8) measurements as
an EPLD frequency value with new analogue cards. (The settings for analogue channels 4/12 to 8/16 are converted,
these channels are automatically recorded into group 1/2.)
" Caution!
Only for service purposes.
CPU No. CPU number. Please state this code if you have questions about the device.
Unit run time Displays the device's total operating time. Please state this code if you have questions about the device.
LCD run time Displays the total operating time of the screen's back lighting. Please state this code if you have questions about the
device.
Simulation “Normal operation”: the device works with the true connected signals.
“Simulation”: the device works with simulated signals. The current device settings are taken into consideration here.
During this time, the true measured value display and storage are switched off. Instead, the simulated values are dis-
played / saved.
! Note!
If required, use the “Signal analysis- Reset” function, so that the values of the simulated signals do not corrupt your true
minima/maxima/quantities after switching back to normal operation.
If the previous signals are still required, save them first on the ATA flash card (see Chapter on “Procedure in operation -
Accessible functions - ATA flash”).
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Related products and manuals for Measuring & layout tools Promag CON-485 Series
(40 pages)© 2020, manymanuals.com. All rights reserved. | 2.244 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals