Promag CON-485 Series Operations Instructions Page 26
- Page / 98
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5 Operation / adjusting device settings - Set-up to commissioning Memo-Graph S
26 Endress+Hauser
Input principle:
1. Begin changing each parameter with “↵”.
2. Use “↓” or “↑” to leaf through values, symbols, selection lists.
3. If the parameter is set correctly, use “↵” to confirm.
!
Note!
– Any settings that are displayed in grey can not be selected / can not be changed (only notes, or
option not available/not activated).
– With the factory setting “0000” (delivery status), configuration is possible at any time. It can be
protected against unauthorised manipulation by entering a 4-digit release code. This has to be
entered when the settings are later changed, if the device settings are to be changed by key-
board.
Tip: make a note of your release code. Store it somewhere where unauthorised persons do not have
access to it.
– The changed settings do not become effective until you return to normal operation by repea-
tedly pressing “ESC” and confirming with “↵”. Until this time, the device still works with the
previous data.
5.5 Set-up using PC
You can also put your Safety Data Manager into service and/or configure it via PC. The following
are available for this:
– Front-mounted RS 232 operating interface (3.5 mm jack plug, stereo, protected behind the unit
cover; only available with die-cast front - not with stainless steel front)
– Rear-mounted RS 232 or RS 485 system interfaces (depending on scope of delivery)
!
Note!
You can use the PC software ReadWin
®
2000, which is provided with the Safety Data Manager, to
put the device into service / configure it via PC. You can also download the software directly from
the internet under the followingg address:
www.endress.com/readwin
For further information on ReadWin
®
2000, refer to the operating manual of the software
(BA107R/09).
Installation of PC software:
1. Install the supplied PC software on your computer. The program's Operating Instructions can
be printed out after installation, if required.
2. Call up the program.
"
Caution!
3. Please make the plug connection first, then the connection to your PC. When removing the
connection, proceed in reverse order.
4. Now you can configure your device via PC. For this, please refer to the program's instruc-
tions/help.
Advantages of configuration via PC:
• The device data is saved in a database and can be accessed again at any time.
• Text entries can be carried out more quickly and efficiently by keyboard
• Measured values can also be read out, archived and displayed on the PC with this program.
"
Caution!
Configuration can only be carried out via one interface (RS 232 or RS 485) at a time.
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Related products and manuals for Measuring & layout tools Promag CON-485 Series
(40 pages)© 2020, manymanuals.com. All rights reserved. | 1.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals